You can access your Plex Media Servers by visiting if you configured your domain and DNS records to point to your server IP. If you do not already have an active domain name, you must purchase one for as little as 1-2 dollars. This is accomplished by configuring/setupngindle as a reverse proxy for Plex Media Server, which will be accessed remotely from a computer or network. The Media Library page allows you to add media directories pre-existing in the Media Library section. When enabled by default, media outside can be accessed if you don’t intend to do so, remove the tick mark. The WebUI allows you to configure and finish Plex installation. You will learn how to install Plex Media Server on Linux Mint 20 series in the following tutorial. Plex Media Server’s software is used to store all of your digital media content and access it via a client application, such as your TV, NVIDIA Shield, Roku, and many other platforms. Once you have the Plex Media Server installed, you can use the Plex client app to access your media library and stream your media files to any supported device. You can install the Plex Media Server on Linux Mint by following the instructions on the Plex website. In this guide, we will show you how to remove Plex Mediaserver from your Linux Mint 20 computer. The following command will allow you to update the Plex Media Servern when it is released. To add movies and TV shows to the Plex media server, create a folder named /movies and then ADD them. In order to use Plex Media Server, you must create an account or sign in with an existing account. There are several methods of installing Plex Media Server on Linux Mint. You can stream your music or movies from any computer to any device at your leisure with Plex. You can use Plex Media Server to transform your Linux Mint into a multimedia server by using it as an application. Your Plex Media Server should now be accessible from other computers on your network. Select the checkbox next to “Plex Media Server” to enable the service. Find “Plex Media Server” in the list of services. Open the Linux Mint firewall configuration tool. You should play with the Synology RAID calculator to find a setup that’s right for you.Assuming you have installed Plex Media Server on Linux Mint, the following instructions will show you how to allow Plex Media Server through the Linux Mint firewall. NAS devices are purpose-built for RAID backups, and as I mentioned earlier, a NAS device with four drive bays is much more secure and provides more usable storage space than a device with just two drive bays. You can set Windows to automatically back up content to this spare drive with the operating system’s built-in backup tool, or achieve the same results on Linux with rsync. If you can spare some cash, you might want to grab a backup drive for all your media files. Remember, hard drives and SSDs don’t last forever. (If you’re using a Raspberry Pi or NVIDIA Shield device, don’t worry about it, your device boots from flash storage). If you’re using an old PC to power your Plex server, consider replacing its boot drive with a cheap, low-capacity SSD, such as the Kingston A400. Like any other computer, your Plex server will boot faster with an SSD system drive, and you should notice less lag while navigating its library. While there’s no reason to store your media on an SSD, there are benefits to using an SSD as your Plex Media Server system drive. Consolidating everything into a NAS device makes your Plex server smaller and easier to manage, but NAS devices that are powerful enough to keep up with Plex’s demands are a little expensive. Some people use a NAS device to hold and manage media alongside their Plex server, while others run the entire operation, server and all, on a single NAS device. If you’re familiar with Linux, try using a distro without a GUI to save computer resources and maximize performance. That said, Linux is ideal because it requires little maintenance and is very power efficient. Windows and macOS-based servers offer similar performance to Linux-based servers, so if you aren’t comfortable with Linux, don’t bother using it. Plex works on Windows, Linux, macOS, and dedicated NAS systems like the Synology Diskstation. Of course, you can save a lot of money turning any old PC or laptop into a Plex server, but such a machine will take up a lot of space and use a lot of power. This computer should be small and power efficient, as it requires a wired internet connection and will run 24/7. The most important component of your Plex server is the computer that manages your media files and runs the Plex software.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |